Trails and Paths Addon – Minecraft Bedrock

addon trails and paths (800 x 445)

Trails and Paths addon (Walk and Build) It has 5 levels of configuration and lets you leave tracks for you wherever you go, or build paths as you walk. Can be used in mode Trail, suitable for playing survival just leaving tracks and avoiding getting lost. or the way Path which is more aggressive and creative, and can create great distances along the way.

It has 5 levels. The level must be changed by function via commands.

The commands are:

  • /function t1 -> Trail 1 – Switches to mode with more space.
  • /function t2 -> Trail 2 – Activates the default mode if you switched.
  • /function t3 -> Trail 3 – Changes to Coarse Dirt.
  • /function tp1 -> Path 1 – Creates paths 1 block wide.
  • /function tp2 -> Path 2 – Creates paths 3 blocks wide.
  • /function tp_off -> Disables any active Trail or Path.

By pressing the ESC key, you can check which level is configured.

 

esc e level

Trails Mode

For those who just want to leave a trail in their path. This helps you remember where you’ve been and avoided getting lost.

Create tracks on the following blocks:

  • Dirt over grass
  • Smooth Sandstone on Sand
  • Andesite on Stone
  • Coarse Dirt on Podzol.
  • Remove some top snow.

It has 3 levels.

When starting the game, it is already configured to use level 2, which is the default. Can be changed by command.

1 – Trail 1.

Spaced trails of dirt (may turn to grass over time).

Change to this level, type the command /function t1.

 

trail 1 in forest (800 x 445)

 

2 – Trail 2 (Default).

Trails with good frequency of dirt (can turn into grass over time).

Change to this level, type the command /function t2.

trail 2 2 dirt in plains 2 (800 x 445)

 

trail 2 snow 3 (800 x 445)

 

trail 2 desert (800 x 445)

 

trilhas na montanha (800 x 445)

 

3 – Trail 3 – Coarse Dirt.

Instead of Dirt, it uses Coarse Dirt (the trail does not disappear with time).

Change to this level, type the command /function t3.

 

trail 3 dirt coarse 2 (800 x 445)

 

trail 3 coarse dirt (800 x 445)

 

Path Mode

The more aggressive mode that makes it possible to create paths with a width of 1 or 3 blocks.

Create tracks on the following blocks:

  • Grass path over grass, dirt, and podzol.
  • Andesite on Stone
  • Smooth Sandstone on Sand
  • Remove some top snow.

It has 2 levels.

Can be changed by command. Display message in action bar to remind you that you are in more aggressive mode.

1 – 1 Block Path.

Create spaceless paths with a width of 1 block.

Change to this level, type the command /function tp1.

 

mensagem 1 actionbar

path 1 block (800 x 445)

 

2 – 3 Block path.

Create spaceless paths with a width of 3 blocks.

Change to this level, type the command /function tp2.

level 5 path 3 blocks (800 x 445)

 

path 3 block desert (800 x 445)

 

Disable Trails and Paths.

To disable any active trail or path, enter the command /function tp_off.

Install

  • Download the Trails_and_Paths.mcaddon file.
  • Run the file and wait for it to be imported into Minecraft.
  • Start your world, enter Behaviors Pack and enable the addon.
  • Enter the world and it will already be working in default mode.

Download Trails and Paths Addon

Download “Trails and Paths Addon” Trails_and_Paths.mcaddon – Downloaded 5273 times – 595.12 KB